A smart card is like an “electronic wallet”. Imagine the of electronic data, and the freedom to carry that information anywhere on integrating the smart card with personal computer (PC). This . Electronic Access System Using Microcontroller” are: .. Contact less technology brings many benefits to secure ID systems. Projects, Final Year Project Titles, Electronics Projects based on Microcontroller, electronics projects, circuit diagrams, PCB layouts, 89C51, 89S51, 89C52, 89S52, UNIQUE ID CARD DESIGN FOR PERSONAL DATA TRANSACTIONS USING SOPHISTICATED MULTIPURPOSE CARD USING SMARTCARD. 1,2,3,4 Asst. Professor,Dept. of Electronics, DBACER Nagpur The RFID card reader is used as an identity for a particular users. Keywords—ATM, microcontroller 89c51,GSM Module, RFID Reader, EM Lock hacking passwords and personal information is more and some time it is difficult to remember the PIN number.
|Published (Last):||24 December 2014|
|PDF File Size:||17.88 Mb|
|ePub File Size:||18.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Below final year project ideas and topics guide electronics learners in how systems are built from scratch. We are using a 5V dc motor to drive the vehicle. Sir, I have selected this as my final year project so plz send me complete detail with code to my mail. Is it just me or does it appear like a few of the comments come across like left by brain dead visitors? The above mentioned perzonal based projects list consists of a variety of projects ideas identificatiln use microcontrollers to achieve various informatoin.
Free email signup Get latest projects, articles in your mail box, subscribe to electrifriends Email: Here the command is given through keyboard; it would have been better if we used IR remote control or something of that kind rather than using keyboard for commanding.
Email will not be published required. Vehicle Monitoring and Security System. In auto mode, the vehicle can be programmed to move at a particular place and park there. This pulse must be a identtification of ns wide.
When data is supplied to data pins, a high to low pulse must be applied to this pin in order for the LCD to latch in the data present at the data pins.
Robotic car using 8951 Microcontroller
Vehicle Monitoring and Security System. Circuit diagram is shown below. Check out these robotics products and kits that you can use to get started on building a bot, either totally from scratch or by using a kit. Robotic car using Microcontroller.
Interfacing an LCD to the 8951 Microcontroller
Stepper motor control board. The degree in which the vehicle rotates, and the timing of coming back to the original position can be further adjusted based on our desired. And I also want to know the feature, description and all those think of microcontroller.
Power transistors must be connected to drive the motor.
Dear sir i also want to do this project so please send me all required component and its microcontroller code usijg well in the following Email ID: I need more information about this project.
The enable pin is used by the LCD to latch information presented to its data pins. Robotic car using Microcontroller.
These are connected to pins B0-B7. Robotic car using Microcontroller. They consist of the command control program needed to run the project.
Sir, I have selected this as my final infornation project so plz send me complete detail with code to my mail.
Water level indicator cum controller. To alert the user that the vehicle is deviating an obstacle, a musical sound system is fitted in the vehicle, so that whenever it is deviating any obstacle, it will also play a music microcontrollee.
To generate IR signal IC based astable multivibrator is used.
Robotic car using Microcontroller | – Part 2
Vehicle Monitoring and Security System. The above listed projects are electronics systems that use a variety of microcontrollers to demonstrate various systems. It is recommended to check the busy flag before writing any data to the LCD. Email will not be published required. We are fitting three IR sensors along with the transmitter at the front of the vehicle in such an angle that the sensor will detect the signal only if certain obstacle is placed at the front of the vehicle at a distance of around 3 inches.
This range of detection can be further adjusted by adjusting the amplitude of transmitter or by adjusting the angle of alignment between the transmitter and the sensor. The function of each pin is given in table. The RS pin is used for their selection as follows. In our model, we have put three sensors at the front of the vehicle, so it is up to the user that, by what angle the vehicle should deviate.
Further, while moving, if any obstacle comes on its path, it will deviate and come to its original path after deviating.
The circuit diagram of the transmitter and the receiver are given below:. All these sensors work independently knformation can sense the obstacle that comes at the front of the vehicle through different position independently. Microcontrollers are programmable units that allow the development of efficient electronics systems with ease.
Interfacing an LCD to the Microcontroller |
Electronic Identification and Personal Information card using Microcontroller. The rear wheel of the vehicle is connected to this motor through a pulley. A 5V dc Stepper motor is fixed at the front wheel lever directly. A0, A1, A2, A3 are the signals coming from the micro controller.
Want to build your own robot? As a result the monostable is triggered and a short pulse is applied to port 2.